Showing posts with label Hackaday Prize. Show all posts
Showing posts with label Hackaday Prize. Show all posts
Tuesday, May 2, 2017
Project viEwMotion
The goal of viEwMotion is to facilitate communication for individuals who have difficulty expressing emotions due to inherent neurologic issues like Autism, Parkinsons, etc (conditions that make it hard express emotion outwardly and as a result for others to read emotion expressed by the effected individual). viEwMotion will do this by interpreting real time physiological data acquired from a wristband which is then processed by a single board computer and displayed to allow others to see the persons emotional state. This will have a profound effect on the ability of people to communicate effectively - changing how they experience and interact with the world around them (in effect changing the world for them and those they interact with).
viEwMotion is a wearable device (worn on the wrist like a watch), that monitors and transmits data to a mini computer which interprets the data and outputs it to a display worn by the individual.
Sunday, April 23, 2017
Sunday, February 5, 2017
Project Voight-Kampff
My objective is to build a functional
Voight-Kampff machine from the classic Sci-Fi Movie Blade Runner.
Leon's test :
Rachel's test:
Currently, I'm working on developing
the software, integration of sensors and the actual body of the
machine.
I currently have this project entered
in the Hackaday Sci-Fi Contest
(Voight-Kampff Project Page) and I plan to exhibit it at the Chicago 2017 Maker Faire.
I have much of the mechanics (arm
raise, extension, and rotation of the eye sensor) worked out using
servos and micro-controllers.
My current design calls for using a
Raspberry Pi as the central processor for the VK. The sensors that
I'm currently working on integrating are:
- Melexis MLX90614 Non-contact Temperature sensor (for Blush response)
- Raspberry Pi NoIR Camera Board v2
- using software adapted from PyGaze to measure pupil dilation/constriction
- Separate hand held module for test subject containing:
- MAX30100 pulse ox sensor
- Galvanic Skin Response Sensor
I aim to have it all contained in the
classic VK machine with read outs from the sensors going to the 3
separate monitors (and the 2 LED Bar Graphs).
Monday, January 16, 2017
Update for the Start of 2017
Sorry for the long hiatus ...
Getting to the Finals of the Hackaday Prize and trying to get my project to a functional prototype really burned me out for a little while - I needed a little rest but I'm back now.
Have a look at the winning entries for the Hackaday Prize 2016 (they are really amazing).
Not that I've ever stopped making stuff, just that I took a break from working on my Universal Glucose Meter, etc... and worked on some other areas for a bit.
Here's some stuff I've been busy with since November 2016:
Getting to the Finals of the Hackaday Prize and trying to get my project to a functional prototype really burned me out for a little while - I needed a little rest but I'm back now.
Have a look at the winning entries for the Hackaday Prize 2016 (they are really amazing).
- Hackaday Prize
- Hackaday Prize 2016 - Submissions
- Final 10 Entries of the 2016 Hackaday Prize
- First Place for the 2016 Hackaday Prize
- Top 5 for the 2016 Hackaday Prize
Not that I've ever stopped making stuff, just that I took a break from working on my Universal Glucose Meter, etc... and worked on some other areas for a bit.
Here's some stuff I've been busy with since November 2016:
- Cheapo SphereBot (from salvaged parts)
- Portable Oscilloscope Build (from kit, mostly)
- Reflow Oven (ControLeo 2, some very minor additions from me)
- 2 Watt LED (445nm) Laser for 3D Printer, CNC (kit build, and review)
- Sous Vide Build
Tuesday, November 1, 2016
Chicago Southland Mini Maker Faire 2016
A basic word of warning to others: Static Electricity Generators are not a great idea in high humidity conditions (relative humidity inside was over 50%). My Van De Graaff generator experienced a mess of problems - from belt problems (thankfully I brought a backup with me), alignment of brushes and (of course) output. The size of my Van De Graaff should make discharges at least a foot long - due to humidity I could only achieve about 1/2 inch.
This years Faire was great, even with the hot and humid weather (we were all, thankfully, inside).
See Pictures below:
Hackday Prize 2016 Round 4 (Home Automation) Winners
Direct Link: Hackaday Prize Home Automation Challange Winners
- RelayRepRap
- HeadsUp, A Low-Cost Device To Diagnose Concussions
- Self Replicating CNC For 194 (Or More) Countries
- 3D Printable Portable Slit Lamp
- Alarm Detection For Hearing Impaired
- Automated LED/Laser Diode Analysis and Modeling
- MyComm
- sdramThingZero – 133MS/s 32-Bit Logic Analyzer
- Evive: A Prototyping Platform For Makers
- Mycodo | Environmental Regulation System
Monday, October 31, 2016
Hackaday Prize 2016: I'm a Round 5 Winner
Hackaday Prize 2016 Assistive Technologies Challange winners: Article Link to Hackaday.com
Again, my Universal Glucometer project made it to the top 20. Below are links to the project pages of the top 20 winners for the Assistive Technologies Challange:
Again, my Universal Glucometer project made it to the top 20. Below are links to the project pages of the top 20 winners for the Assistive Technologies Challange:
- AutoFan – Automated Control of Air Flow
- Open Source Arduino Blood Glucose Meter Shield
- Shakelet – Alerts For The Hard Of Hearing
- A Modular, Low-Cost Braille Electronic Display
- TNS B1i
- Humidifeyes
- Pallette
- CastMinder – The Cast And Splint Monitoring System
- Low-Cost Tongue Vision
- FLipMouse
- Affordable Diagnostic Thermal Incubator
- Refreshable Braille Display
- Raimi’s Arm – Bionic Arm For Kids
- BEOWULF
- Facade: Tactile Interfaces To Appliances
- Antigravity Arm Floats
- Dextra
- Universal Glucometer
- 3D Prints For Teachers Of The Visually Impaired
- BOSI- BlueTooth Open Source Switch Interface
Monday, October 10, 2016
Thursday, July 21, 2016
Hackaday Prize 2016 - I'm a Round 3 Winner
I'm so amazed, overjoyed and honored that my Universal Glucometer project actually made the Top 20 of the 2016 Hackaday Prize - Citizen Scientist Round .
I've got a lot of work ahead of me - primarily on the coding side, but I'm determined and I WILL get it done, along with a fully functional prototype.
Here is a list of all 20 Winners of Round 3 Citizen Scientist Round:
I've got a lot of work ahead of me - primarily on the coding side, but I'm determined and I WILL get it done, along with a fully functional prototype.
Here is a list of all 20 Winners of Round 3 Citizen Scientist Round:
- MyComm
- Open Source Arduino Blood Glucose Meter Shield
- CODE RED
- Neuroscience of Grasshopper Jumps
- Flypi – Cheap Microscope/Experimental Setup
- Spectrophotometer
- Alli-GAIT-or Analysis
- Internet Of Things Microscope
- PULSE : Profiling Underwater Light SEnsor
- Affordable Reflectance Transformation Imaging Drone
Labels:
diabetes,
diy,
Hackaday Prize,
hacking,
maker faire,
PIC,
project
Tuesday, July 12, 2016
2016 Hackaday Prize, moving into round 4
So far 3 of the 5 rounds for the Hackaday Prize 2016 (this years theme is - "Build Something That Matters") have finished:
- Design Your Concept (March 14 - April 25)
- Anything Goes (April 25 - May 30)
- Citizen Scientist (May 30 - July 11) just finished, no results yet
The top entries for rounds 1 and 2 are listed below:
The top 20 projects of theHackaday Prize 2016 "Design Your Concept" challengeare:
The top 20 projects of the 2016 Hackaday Prize "Anything Goes"challenge are:
- Automatic Digital Microscope (also in top 20 of round 1)
- ICeeData (also in top 20 of round 1)
The Citizen Scientist Challenge (Round
3) just finished yesterday and that marks the start of the Home
Automation Challenge (Round 4), to be followed by the Assistive Technologies Challenge (Round 5) which is the last round before finals.
In the next few days we should have news of the to 20 projects in Round 3, that will be added to the list of the top 100 projects going into the Finals.
My 2 entries to the Hackay Prize 2016 (Universal Glucometer and Train Your Brain) have not yet made it to the top 20 of any round so far ( ;( ), but I continue to work on them both.
Project: Universal Glucometer - in the news (well... sort of)
While trying to show a friend my Universal Glucometer entry for the 2016 Hackaday Prize, I came across this article: Hackaday Prize Entry: A Universal Glucose Meter.
It was definitely a nice surprise, I must have missed notifications in my feeds.
It was definitely a nice surprise, I must have missed notifications in my feeds.
Sunday, June 19, 2016
Project Universal Glucomter - 1st Contact
I posted the basic details of this on Hackaday earlier, thought I's post the some of the nitty gritty details here.
I decided to take a step back and return to some real basic level stuff for programming and using PIC Microcontroller's. First order of business was to ensure my programmer (PICkit3 clone) actually works and that I can actually upload programs (I know compiling programs works but I haven't actually uploaded anything) . Back when I ordered my last LCD screen (which is actually the wrong one for the reference design from Microchip) I also ordered a few PIC16F877A chips since I have some books that use them for learning to code in C for PIC's.
The first program I wanted to try was the most basic, a simple "Hello World" program that blinks an LED. The tutorial I worked from was Blink LED with PIC16F877A. The first hurdle I needed to make it over was how to actually connect the PICkit3 to the micro-controller (in hindsight, if I had started with a Development Board this would not have been an issue). Bread boarding the circuit was no problem from the schematic:

As I put together the circuit on a solderless bread board I realized that I did not order any crystals for the timer oscillator (I'd spent so much time going over the datasheet for the PIC16F1786, from the glucometer reference design, that I never realized that the 877A has no internal oscillator). After going through crystals I scavenged from old electronics, I found a 4MHz ceramic (3 pin, no need for external capacitors) oscillator. I didn't really know if it still worked after de-soldering it from devices and I'm not really sure how I could test it but took my chances and used it anyway.
After everything was assembled I needed to connect the PICkit3 programmer. Pin #1 is designated on the connected by a solid white arrow. Pin functions are:
1 = MCLR/VPP
2 = VDD Target (power)
3 = VSS (ground)
4 = PGD (ICSPDAT)
5 = PGC (ICSPCLK)
6 = PGM (LVP)
VDD and VSS could easily have confused me but I knew from prior reading that VDD is + power and VSS is ground. That leaves the other 4 pins - actually 3 since pin 6 is not used here. Referring to the pin out for the PIC16F877A chip:
The MCLR/Vpp pin is obviously pin 1 of the chip. Looking at the diagram, you may think , as I did, that pins 25 and 26 are the Clock and Data pins. As I found out - that is wrong, PGD (ICSPDAT) is the Data pin (pin 40) and PGC (ICSPCLK) is the Clock pin (pin 39). In addition to this, there are a few other points to consider:
#pragma config FOSC = XT // Oscillator Selection bits (XT oscillator)
My other Configuration Bit settings were:
#pragma config WDTE = OFF // Watchdog Timer Enable bit (WDT disabled)
#pragma config PWRTE = OFF // Power-up Timer Enable bit (PWRT disabled)
#pragma config BOREN = ON // Brown-out Reset Enable bit (BOR enabled)
#pragma config LVP = OFF // Low-Voltage (Single-Supply) In-Circuit Serial Programming Enable bit (RB3 is digital I/O, HV on MCLR must be used for programming)
#pragma config CPD = OFF // Data EEPROM Memory Code Protection bit (Data EEPROM code protection off)
#pragma config WRT = OFF // Flash Program Memory Write Enable bits (Write protection off; all program memory may be written to by EECON control)
#pragma config CP = OFF // Flash Program Memory Code Protection bit (Code protection off)
It's taken me a few days of reading, trial, and error but I've finally gotten an LED to blink (pretty impressive right!).
Next step is attaching and sending text to a standard 16x2 LCD.
If I have to I will stick with the PIC16F877A, but if I do I'll at least need an external Op-Amp connected (to amplify the signal from the strip). Hopefully I'll be able to return to the 16F1786 and won't need to deal with that.
I decided to take a step back and return to some real basic level stuff for programming and using PIC Microcontroller's. First order of business was to ensure my programmer (PICkit3 clone) actually works and that I can actually upload programs (I know compiling programs works but I haven't actually uploaded anything) . Back when I ordered my last LCD screen (which is actually the wrong one for the reference design from Microchip) I also ordered a few PIC16F877A chips since I have some books that use them for learning to code in C for PIC's.
The first program I wanted to try was the most basic, a simple "Hello World" program that blinks an LED. The tutorial I worked from was Blink LED with PIC16F877A. The first hurdle I needed to make it over was how to actually connect the PICkit3 to the micro-controller (in hindsight, if I had started with a Development Board this would not have been an issue). Bread boarding the circuit was no problem from the schematic:

As I put together the circuit on a solderless bread board I realized that I did not order any crystals for the timer oscillator (I'd spent so much time going over the datasheet for the PIC16F1786, from the glucometer reference design, that I never realized that the 877A has no internal oscillator). After going through crystals I scavenged from old electronics, I found a 4MHz ceramic (3 pin, no need for external capacitors) oscillator. I didn't really know if it still worked after de-soldering it from devices and I'm not really sure how I could test it but took my chances and used it anyway.
After everything was assembled I needed to connect the PICkit3 programmer. Pin #1 is designated on the connected by a solid white arrow. Pin functions are:
1 = MCLR/VPP
2 = VDD Target (power)
3 = VSS (ground)
4 = PGD (ICSPDAT)
5 = PGC (ICSPCLK)
6 = PGM (LVP)
VDD and VSS could easily have confused me but I knew from prior reading that VDD is + power and VSS is ground. That leaves the other 4 pins - actually 3 since pin 6 is not used here. Referring to the pin out for the PIC16F877A chip:
The MCLR/Vpp pin is obviously pin 1 of the chip. Looking at the diagram, you may think , as I did, that pins 25 and 26 are the Clock and Data pins. As I found out - that is wrong, PGD (ICSPDAT) is the Data pin (pin 40) and PGC (ICSPCLK) is the Clock pin (pin 39). In addition to this, there are a few other points to consider:
- 100uF ceramic caps across pins 11/12 and 31/32
- pullup resistor on MCLR/Vpp (pin 1) - around 5-10K
#pragma config FOSC = XT // Oscillator Selection bits (XT oscillator)
My other Configuration Bit settings were:
#pragma config WDTE = OFF // Watchdog Timer Enable bit (WDT disabled)
#pragma config PWRTE = OFF // Power-up Timer Enable bit (PWRT disabled)
#pragma config BOREN = ON // Brown-out Reset Enable bit (BOR enabled)
#pragma config LVP = OFF // Low-Voltage (Single-Supply) In-Circuit Serial Programming Enable bit (RB3 is digital I/O, HV on MCLR must be used for programming)
#pragma config CPD = OFF // Data EEPROM Memory Code Protection bit (Data EEPROM code protection off)
#pragma config WRT = OFF // Flash Program Memory Write Enable bits (Write protection off; all program memory may be written to by EECON control)
#pragma config CP = OFF // Flash Program Memory Code Protection bit (Code protection off)
It's taken me a few days of reading, trial, and error but I've finally gotten an LED to blink (pretty impressive right!).
Next step is attaching and sending text to a standard 16x2 LCD.
If I have to I will stick with the PIC16F877A, but if I do I'll at least need an external Op-Amp connected (to amplify the signal from the strip). Hopefully I'll be able to return to the 16F1786 and won't need to deal with that.
Monday, June 13, 2016
Project Updates
Sorry I haven't updated this blog for quite a while - it's due to working on projects over at Hackaday.
I currently have 2 entries for this years Hackaday Prize.
- Open Source Neurofeedback (click for details)
- Universal Glucometer (click for details)
For my Open Source Neurofeedback project my main challenge continues to be learning to program in Java.
- While I do have experience in BASIC, PASCAL, batch files for MS DOS, some C and just a little Python and am reasonably comfortable with linux command line stuff. While I can read Java programs and understand them, learning to write my own is taking a bit longer than expected. But, I am starting to get the hang of it.
- The hardware side of this project is fairly straight forward, even with a few modifications I've made as I've been prototyping.
My Universal Glucometer project has presented me with a number of challenges:
- While Microchip provides some base code for a glucometer along with a test layout - some parts are no longer available or difficult to find - which goes counter to my idea of a glucometer that can be built from basic parts and adapted to different test strips. Due to these issues I've decided that I need to change code to use a different LCD (the LCD in the Application Note is hard to find - I actually ordered the wrong one -twice - same manufacturer but different pin-out and control protocol). So, if it is a problem for me to find it now, it'll be worse for others later - need to use an easier to find/source display (maybe a standard 16x2 LCD or a Nokia LCD display - both are easy to get cheap on Ebay).
- The biggest challenge I've had is figuring my way around Microchip's Microcontrollers: writing code for them and uploading code. I only recently moved into programming AVR's instead of Arduino's and in hindsight it would have been easier to start with a development board and then worked up to a bare chip (like going from Arduino to AVR's). It took me awhile, but I finally got MPLAB (Microchip's IDE - Integrated Development Enviornment) installed, along with XC8 (Microchips C compiler for their 8 bit microcontrollers). I even got the demo program for Glucose Meter to compile. I am still trying to upload it to the actual microcontroller using MPLAB and PICkit3.
Wednesday, April 13, 2016
Hackaday World Create Day 2016 and Hackaday Prize 2016
Only 1 week from this Saturday, on April 23rd, it's:
I'll be hosting a Meetup in Plainfield, IL at the Plainfield Public Library to meet and brainstorm ideas for entries to this years Hackaday Prize. Plainfield, IL World Create Day
From Hackaday.io:
World Create Day - Event Details
Create tech solutions for social change on Hackaday World Create Day, our worldwide brainstorming session for the 2016 Hackaday Prize design concept challenge! Join teams from around the globe and submit ideas for projects that solve problems in categories from citizen science to assistive technologies, or anything else that leverages your hardware, coding, scientific, design and mechanical skills.We’ll be picking the most spectacular design solutions to share on the Hackaday front page, and there will be prizes. But we also want to celebrate the fun of getting together in person with all of the people who make Hackaday a part of their daily ritual, so share your photos and ideas with hashtag #WorldCreateDay!
The Goal:
Form a team (or work on your own) and submit a project to the Hackaday Prize design challenge. See challenge details here: https://hackaday.io/prize/details#oneNeed some inspiration for your project? Here are some ideas:
- Citizen Science - Build a graphene supercapacitor, study the effects of a behavior, build an open source instrumentation device.
- Automation - Build a device that makes breakfast or buys laundry detergent when you’re running low. Automatically track stuff, automate any process, build a Me-robot to do your every whim
- Assistive technologies - Build a project that helps others move better, see better, or live better. Whether that means exoskeletons, a better wheelchair, a braille display, or educational software, we want to see it.
- Or any other idea you have to hack for social change! Leverage your talent and find solutions to address technology issues facing humanity today.
Beyond Hackaday World Create Day Meetup
Hackaday World Create Day is a single event, but your meetup can live on if you want it to. We can help with ideas for future meetups of your group. This is a great way to show that the Hackaday community is alive and thriving in your part of the world. Maybe our next big event will be held in your city!Thursday, June 25, 2015
My Hackaday Prize entry
Finally decided on a project for the Hackaday Prize. It's been going around in my head for awhile so I already have an approach and done a bunch of research into the science for this idea.
You can check it out here Stripless-bG-Measurement for Diabetes management.
You can check it out here Stripless-bG-Measurement for Diabetes management.
Thursday, May 14, 2015
Hackaday Prize
I've liked the Hackaday site and the Hackaday Prize for quite a while. They are wonderful sources of new ideas and inspiration.
The 2015 competition opened two months ago (when I originally wrote this post) and the focus is on ideas that address important issues effecting lots of people.
I've been brainstorming ideas for a project for the competition and areas I've focused on are:
Water
The 2015 competition opened two months ago (when I originally wrote this post) and the focus is on ideas that address important issues effecting lots of people.
I've been brainstorming ideas for a project for the competition and areas I've focused on are:
Water
- Solar purification/desalination
- Collection techniques - reclaim from air, rain, etc
- Potability measurement device (determine if water is safe to drink)
- more efficient bG testing/measurement
- bG testing method without strips
- bG testing method without using lancet (no finger pricks)
- open source/hardware meter that can utilize multiple strip types
- methods for detecting allergens
- protein based allergens
- other types
- what data can we collect?
Subscribe to:
Posts (Atom)


